System Bootstrap, Version 5.2(5), RELEASE SOFTWARE Copyright (c) 1986-1994 by cisco Systems 2500 PRocessor with 2048 Kbytes of main memory 大約停頓1-2分鐘,系統調入boot,請耐心等待
F3: 3996764+54172+225404 at 0x3000060
Restricted Rights Legend
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-I-L), Version 11.2(1), MAJOR RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Mon 30-Sep-96 12:07 by ajchopra Image text-base: 0x030215A4, data-base: 0x00001000
cisco 2500 (68030) processor (revision D) with 2048K/2048K bytes of memory. Processor board ID 02327592, with hardware revision 00000000 Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSip compliant. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System Flash (Read ONLY)
Notice: NVRAM invalid, possibly due to write erase. --- System Configuration Dialog ---
At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Would you like to enter the initial configuration dialog? [yes]:Return 你是否要進入初始化配置?默認"是".
First, would you like to see the current interface summary? [yes]:Return 首先,你是否想看一下當前端口的狀態?默認"是".
Any interface listed with OK? value "NO" does not have a valid configuration 下面會列出當前路由器所具有的硬件配置(包括局域網口和廣域網口,以及個端口當前狀態等等.)
Interface IP-Address OK? Method Status Protocol Ethernet0 unassigned NO unset up down Serial0 unassigned NO unset down down Serial1 unassigned NO unset down down
Configuring global parameters:
Enter host name [Router]: JSRouter 設置系統名,如JSRouter.
The enable secret is a one-way cryptographic secret used instead of the enable passWord when it exists.
Enter enable secret: cisco 設置進入priviledged EXEC 的密碼
The enable password is used when there is no enable secret and when using older software and some boot images.
Enter enable password: cisco1 (1) Enter virtual terminal password: cisco 設置進入虛擬終端登錄到路由器的口令,即遠程登錄(telnet)的口令 Configure SNMP Network Management? [yes]:Return 是否設置簡單網管協議? Community string [public]:Return
Configure IP? [yes]:Return 是否設置IP協議? Configure IGRP routing? [yes]:Return (2) 是否設置IGRP 路由協議? Your IGRP autonomous system number [1]:Return (3) 你的IGRP 路由協議自治系統號(AS),默認為1.
Configuring interface parameters: 下面配置端口參數
Configuring interface Ethernet0:Return Is this interface in use? [yes]:Return Configure IP on this interface? [yes]:Return IP address for this interface: 1.1.1.1 Number of bits in subnet field [0]:Return (4) Class A network is 1.0.0.0, 0 subnet bits; mask is /8 以上是配置以太口0,假設IP地址是1.1.1.1,掩碼是255.0.0.0.
Configuring interface Serial0:Return Is this interface in use? [yes]:Return Configure IP on this interface? [yes]:Return Configure IP unnumbered on this interface? [no]:Return IP address for this interface: 2.1.1.1 Number of bits in subnet field [0]:Return Class A network is 2.0.0.0, 0 subnet bits; mask is /8 以上是配置串口0,假設IP地址是2.1.1.1,掩碼是255.0.0.0.
Configuring interface Serial1:Return Is this interface in use? [yes]: no 以上是當不需要用串口1時,請敲入no.
The following configuration command script was created:
hostname JSRouter enable secret 5 $1$Bv.r$j/Zm2B6jw9UTQPxLGZjAz. enable password cisco1 line vty 0 4 password cisco snmp-server community public !
ip routing ! interface Ethernet0 ip address 1.1.1.1 255.0.0.0 ! interface Serial0 ip address 2.1.1.1 255.0.0.0 ! interface Serial1 shutdown no ip address ! router igrp 1 network 1.0.0.0 network 2.0.0.0 ! end
Use this configuration? [yes/no]: yes (5) 確認當前配置后,把當前配置寫入NVRAM 中.這樣以后開機自動把配置調入內存,不需要重新配置了.
Building configuration... Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down %LINK-3-UPDOWN: Interface Ethernet0, changed state to up %LINK-3-UPDOWN: Interface Serial0, changed state to down %LINK-3-UPDOWN: Interface Serial1, changed state to down %LINK-5-CHANGED: Interface Serial1, changed state to administratively down %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-I-L), Version 11.2(1), MAJOR RELEASE SOFTWARE (fc1 ) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Mon 30-Sep-96 12:07 by ajchopra JSRouter>en Password:(敲入密碼,不反顯的) JSRouter#
備注:
Enter enable password:-----這個口令是對于IOS 10.2以下版本適用,在IOS 10.3以上版本均使用secret,不再用password.在配置文件中, secret是加密顯示的. 現在我們通常都在IOS 10.3 版本以上,故無需password這個口令. 另外,password和secret不能相同.
Number of bits in subnet field [0]-----掩碼子網的位數.舉例說明: 掩碼為255.0.0.0的掩碼子網位數是0,掩碼共8位 掩碼為255.255.0.0的掩碼子網位數8,掩碼共16位 掩碼為255.255.255.0的掩碼子網位數16,掩碼共24位 掩碼為255.255.255.252的掩碼子網位數22,掩碼共30位 Cisco命令系統是即時生效的,也就是說,配置完后立即執行,但若不寫入NVRAM 中,關掉電源后就會丟失.你若想保留更改的配置,請敲入write命令. Windows 95/NT 下,超級終端的設置. 在 開始--->程序--->附件--->超級終端--->Hypetrm 設定名稱為cisco,再選擇一個圖標. 請選擇"直接連接到串口1" 選擇波特率為9600bps. 最后把設置的保存在cisco文件里.下一次直接從超級終端cisco中啟動.
